Services

Service not listed?  Shoot us an email to RefinedPerformance@Gmail.com !
Service Description Labor 
Car Deck Installation  -Remove and reinstall any dash panels necessary to access the deck opening $30
-Remove existing deck
-Connect a wiring harness (sold separately) to allow the new deck to plug into the vehicle's factory wiring and facilitate reinstallation of the factory deck (if you sell the vehicle)
-Install any required dashboard kits (sold separately) to ensure an integrated, factory-installed appearance
-Install any required antenna adapters (sold separately) to provide clear AM/FM reception
-Attach any antenna connections
 
Excludes
-Hardware & Installation parts
-Custom labor such as dash board cuts, installs where no radio was installed previously, etc.(For custom jobs email refinedperformance@gmail.com !)
In-Dash Navigation or In-Dash Video Installation -Remove and reinstall any dash panels necessary to access the deck opening $60
-Remove existing deck
-Connect a wiring harness (sold separately) to allow the new deck to plug into the vehicle's factory wiring and facilitate reinstallation of the factory deck (if you sell the vehicle)
-Install any required dashboard kits (sold separately) to ensure an integrated, factory-installed appearance
-Install any required antenna adapters (sold separately) to provide clear AM/FM reception
-Attach any antenna connections
 
Excludes
-Hardware & Installation parts
-Custom labor such as dash board cuts, installs where no radio was installed previously, etc.(For custom jobs email refinedperformance@gmail.com !)
Basic Speaker Installation -Remove and reinstall any grilles necessary to access the vehicle's factory speaker locations $20
-Remove existing speakers
-Connect a wiring harness (sold separately) to existing speaker wiring to allow speakers to remain in phase and enable factory speakers to be reinstalled when you sell the vehicle
-Install new component speakers (pair) behind existing grilles to maintain original factory appearance
-Ensure speaker phasing is correct for the best possible sound
 
Excludes
-Removal of door panel or seat
-Component speaker installation
-Hardware & Installation parts
-Custom labor such as door cuts, installs where no speaker was installed previously, etc.(For custom jobs email refinedperformance@gmail.com !)
Standard Speaker Installation  -Remove and reinstall any panels necessary to access the vehicle's factory speaker locations $30
-Remove existing speakers
-Connect a wiring harness (sold separately) to existing speaker wiring to allow speakers to remain in phase and enable factory speakers to be reinstalled when you sell the vehicle
-Install new component speakers (pair) behind existing grilles to maintain original factory appearance
-Ensure speaker phasing is correct for the best possible sound
 
Excludes
-Component speaker installation
-Hardware & Installation parts
-Custom labor such as door cuts, installs where no speaker was installed previously, etc.(For custom jobs email refinedperformance@gmail.com !)
Component Speaker Installation  -Remove and reinstall any panels necessary to access the vehicle's factory speaker locations $50
-Remove existing speakers
-Connect a wiring harness (sold separately) to existing speaker wiring to allow speakers to remain in phase and enable factory speakers to be reinstalled when you sell the vehicle
-Install new component speakers (pair) behind existing grilles to maintain original factory appearance
-Install crossovers for component speakers
-If necessary, consult with you to determine mounting locations of separate tweeters
-Ensure speaker phasing is correct for the best possible sound
 
Excludes
-Hardware & Installation parts
-Additional charges that some installations require*
-Custom labor such as door cuts, installs where no speaker was installed previously, etc.(For custom jobs email refinedperformance@gmail.com !)
2-Channel or Mono Car Amplifier Installation -Securely mount your mono or 2-channel amplifier in an agreed-upon location, such as in the trunk or rear section of your vehicle $60
-Connect fused power cable to battery and properly ground the amplifier
-Make connections to the deck and speakers, securing and concealing all wiring beneath trim panels or carpeting
-Optimize all amplifier settings to correspond with your vehicle's acoustics and your individual listening preferences
 
Excludes
-Hardware & Installation parts
-Locations under seats or areas where additional parts need to be removed to mount.
4-Channel Car Amplifier Installation -Securely mount your 4-channel amplifier in an agreed-upon location, such as in the trunk or rear section of your vehicle $75
-Connect fused power cable to battery and properly ground the amplifier
-Make connections to the deck and speakers, securing and concealing all wiring beneath trim panels or carpeting
-Optimize all amplifier settings to correspond with your vehicle's acoustics and your individual listening preferences
 
Excludes
-Hardware & Installation parts
-Locations under seats or areas where additional parts need to be removed to mount.
Remote Start Installation -Consult with you to determine mounting location of LED and valet switches $80
-Mount LED and valet switches and route/conceal wiring to control module
-Mount antenna and route/conceal wiring to the control module
-Mount hood switch and route/conceal wiring into the vehicle
-Connect to the following circuits:
-Starter kill, if applicable
-Door trigger, if required
-Tach, if required
-One ignition, one accessory and one starter wire
-One additional wire that can be configured as ignition, accessory or starter
-Constant power
-Parking lights (additional parts may be required)
-Mount/conceal control module
-Test all functions
-Demonstrate unit functionality
 
Excludes
-Hardware & Installation parts
-Additional charges that some installations require*
Security System, Remote Start and Keyless Entry Installation Consult with you to determine mounting location of LED and valet switches $120
Mount siren in a secure location and route/conceal wiring into the vehicle
-Mount LED and valet switches and route/conceal wiring to control module
-Mount antenna and route/conceal wiring to the control module
-Mount shock sensor and route/conceal wiring to the control module
-Mount hood switch and route/conceal wiring into the vehicle
-Connect to the following circuits:
-Starter kill
-Door trigger (diode isolation additional)
-Tach, if required
-Ignition, accessory and starter power wires
-One additional power circuit: ignition, accessory or starter
-Constant power
-Parking lights (additional parts may be required)
-Door locks (including five-wire and one-wire; additional parts may be required)
-Mount/conceal control module
-Test all functions
-Demonstrate unit functionality
 
Excludes
-Hardware & Installation parts
-Additional charges that some installations require*
Advanced Hands-Free Installation -Consult with you to determine mounting location of the hands-free display and microphone $30
-Mount the display, microphone and control module
-Connect to the following circuits:
-Radio speakers
-Power source
-Conceal control module and wiring
-Test all functions
-Demonstrate unit functionality
 
Excludes
-Hardware & Installation parts
-Additional charges that some installations require*
SmartPhone/MP3 Player In-Car Installation -Hardwire power connection behind the dash, freeing your DC lighter outlet for alternative uses $30
-Mount your MP3 player in an agreed-upon location (with mounting bracket, sold separately)
-Test all functions
-Demonstrate unit functionality
 
Excludes
-Hardware & Installation parts
-Additional charges that some installations require*
Portable GPS/Radar Detector Installation -Hard wire power connection behind the dash, freeing your DC lighter outlet for alternative uses $30
-Mount portable GPS/radar detector in an agreed-upon location (with mounting bracket, if provided with unit)
-Run antenna wire (if provided) through the vehicle and position antenna for optimal reception
-Test all functions
-Demonstrate unit functionality
 
Excludes
-Hardware & Installation parts
-Additional charges that some installations require*